Reach Set, photographed at rest. — The garment as it hangs, with nothing happening to it.

Reach Set, photographed during the movement it is cut for. — The same garment during the movement this line is built around.

SetsF-02

Reach Set

Work Shirt Action-Back and Work Trouser Basic. For days spent with your arms above your head.

Measured movement figures

Squat depth: 42 cm
Knee allowance: 6 cm
Overhead reach: 170°
Back movement: 8 cm

Measurement basis: 165 cm wearer / size 38

Measured on a 165 cm wearer in size 38. Yours will differ.

Your statutory rights

You can report a fault for three years from delivery. For the first two years, if something is wrong, we have to show it wasn't faulty when you got it. Not the other way round.

If we say no to your claim and you disagree, you can take it to Allmänna reklamationsnämnden (ARN). It is free for you, and we will follow their recommendation.

You also have 14 days from delivery to change your mind, for any reason or none. See Ångerrätt and Reklamation.

Try it before it goes to work

When it arrives, squat down in it before you wear it to work. That is the test that matters, and doing it doesn't affect your right to return.

Construction

Work Shirt Action-Back (B-02) — 170° overhead, 8 cm back movement.
Work Trouser Basic (A-01) — 42 cm squat depth, 6 cm knee allowance.
The shirt's extended rear hem is cut to sit under the trouser waistband when both arms go up.

What is in the set

B-02 Work Shirt Action-Back$108
A-01 Work Trouser Basic$88
Bought separately$196
As a set$172

Pockets — position and depth

Pocket positions measured from the waistline, and pocket depths, in centimetres
Pocket	Centre below waistline	Depth
Hip pocket, left and right	9 cm	17 cm
Flapped chest pocket, left and right	22 cm above	15 cm

Finished measurements

These are the measurements of the garment lying flat, not of a body. Every figure is in centimetres and is taken after washing.

Finished garment measurements in centimetres, by size
Size	See each garment
One size	See each garment

Specification

Fabric weight: 300 g/m²
Fibre composition: 60 % cotton, 40 % polyester
Shrinkage: Up to 3 % in length and 2 % in width after the first 60 °C wash.
Origin: Designed in Mariefred. Country of making: [Pending — to be confirmed by the operator before launch].
Purchase type: Outright purchase. No subscription.
Classification: Workwear. Not personal protective equipment. Not certified to any protective standard.

Reinforced here

Pleat heads
Yoke seam
Seat panel
Knee panel

What fails first

Workwear wears out, and it wears out in a predictable order. These are the places this garment gives up first, listed before you buy it rather than after.

1.Pleat head bar tacks
2.Knee panel
3.Shirt elbow

Wear at these points is wear, not a fault. A seam that opens in normal use, a failed zip, a reinforcement layer coming away, a garment that does not match the measurements above, or shrinkage beyond the stated range — those are faults. See Reklamation.

Care

Machine wash 60 °C, normal cycle.
Do not use fabric softener — it coats the twill and the fabric stops shedding dust.
Tumble dry low or line dry.
Iron medium. Do not iron over the hardware.
Wash before first wear so the shrinkage below has already happened when you check the fit.

Also cut for sets

F-01

Squat Set

Work Trouser Basic and Work Shirt Basic. The starting point if your day is mostly low down.

Squat depth: 42 cm
Knee allowance: 6 cm
Overhead reach: 150°
Back movement: 4 cm

$148USD

Figures

F-03

Standing Set

Standing Trouser Wide-Band and Work Shirt Basic. For a day measured in hours on your feet.

Squat depth: 42 cm
Knee allowance: 6 cm
Overhead reach: 150°
Back movement: 4 cm

$172USD

Figures

F-04

Tools Set

Tool Trouser Basic and Tool Vest. Fourteen pockets, every one placed for a 165 cm frame.

Squat depth: 42 cm
Knee allowance: 6 cm
Back movement: 6 cm

$178USD

Figures