Tool Vest, photographed at rest. — The garment as it hangs, with nothing happening to it.

Tool Vest, photographed during the movement it is cut for. — The same garment during the movement this line is built around.

Tools & PocketsD-03

Tool Vest

Eight pockets across the front, all of them above the point where a shorter arm has to bend.

Measured movement figures

Back movement: 6 cm

Measurement basis: 165 cm wearer / size 38

Measured on a 165 cm wearer in size 38. Yours will differ.

Your statutory rights

You can report a fault for three years from delivery. For the first two years, if something is wrong, we have to show it wasn't faulty when you got it. Not the other way round.

If we say no to your claim and you disagree, you can take it to Allmänna reklamationsnämnden (ARN). It is free for you, and we will follow their recommendation.

You also have 14 days from delivery to change your mind, for any reason or none. See Ångerrätt and Reklamation.

Try it before it goes to work

When it arrives, squat down in it before you wear it to work. That is the test that matters, and doing it doesn't affect your right to return.

Construction

Eight pockets: two chest, four mid-front, two lower, all forward of the side seam.
Lowest pocket centre sits 18 cm below the waistline — still reachable without leaning.
Front zip, no collar.
Bar-tacked at every pocket corner.

Pockets — position and depth

Pocket positions measured from the waistline, and pocket depths, in centimetres
Pocket	Centre below waistline	Depth
Chest pocket, left and right	22 cm above	15 cm
Mid-front pocket, two left and two right	6 cm above	17 cm
Lower pocket, left and right	18 cm	19 cm

Pocket positions are set for a 165 cm frame. Scaled-down men's patterns put them where a shorter arm can't reach. Every distance below is measured from the waistline down to the centre of the pocket opening.

Finished measurements

These are the measurements of the garment lying flat, not of a body. Every figure is in centimetres and is taken after washing.

Finished garment measurements in centimetres, by size
Size	Chest	Back length	Shoulder
34	100 cm	62 cm	38.4 cm
36	104 cm	63 cm	39.2 cm
38	108 cm	64 cm	40 cm
40	112 cm	65 cm	40.8 cm
42	116 cm	66 cm	41.6 cm
44	120 cm	67 cm	42.4 cm
46	124 cm	68 cm	43.2 cm

Specification

Fabric weight: 320 g/m²
Fibre composition: 60 % cotton, 40 % polyester
Shrinkage: Up to 3 % in length and 2 % in width after the first 60 °C wash.
Origin: Designed in Mariefred. Country of making: [Pending — to be confirmed by the operator before launch].
Purchase type: Outright purchase. No subscription.
Classification: Workwear. Not personal protective equipment. Not certified to any protective standard.

Reinforced here

All pocket corners
Zip tape ends
Shoulder seam

What fails first

Workwear wears out, and it wears out in a predictable order. These are the places this garment gives up first, listed before you buy it rather than after.

1.Lower pocket corners
2.Zip tape ends
3.Armhole binding

Wear at these points is wear, not a fault. A seam that opens in normal use, a failed zip, a reinforcement layer coming away, a garment that does not match the measurements above, or shrinkage beyond the stated range — those are faults. See Reklamation.

Care

Machine wash 60 °C, normal cycle.
Do not use fabric softener — it coats the twill and the fabric stops shedding dust.
Tumble dry low or line dry.
Iron medium. Do not iron over the hardware.
Wash before first wear so the shrinkage below has already happened when you check the fit.

Also cut for tools & pockets

D-01

Tool Trouser Basic

Six pockets, every one of them placed for a 165 cm frame rather than scaled down from 180 cm.

Squat depth: 42 cm
Knee allowance: 6 cm

$68USD

Figures

D-02

Tool Trouser Deep

24 cm thigh pockets. Deep enough that a long screwdriver stops working its way out.

Squat depth: 42 cm
Knee allowance: 6 cm

$118USD

Figures

D-04

Tool Belt Fabric

A woven belt pouch, no leather. Adjustable from 68 to 118 cm.

$88USD

Figures