Work Shirt Sleeveless, photographed at rest. — The garment as it hangs, with nothing happening to it.

Work Shirt Sleeveless, photographed during the movement it is cut for. — The same garment during the movement this line is built around.

Reach & ClimbB-06

Work Shirt Sleeveless

No sleeve, so no armhole limit. 8 cm of back movement from the pleats.

Measured movement figures

Back movement: 8 cm

Measurement basis: 165 cm wearer / size 38

Measured on a 165 cm wearer in size 38. Yours will differ.

Your statutory rights

You can report a fault for three years from delivery. For the first two years, if something is wrong, we have to show it wasn't faulty when you got it. Not the other way round.

If we say no to your claim and you disagree, you can take it to Allmänna reklamationsnämnden (ARN). It is free for you, and we will follow their recommendation.

You also have 14 days from delivery to change your mind, for any reason or none. See Ångerrätt and Reklamation.

Try it before it goes to work

When it arrives, squat down in it before you wear it to work. That is the test that matters, and doing it doesn't affect your right to return.

Construction

Bound armholes, no sleeve.
Two box pleats from the yoke.
Flat-felled shoulder and side seams.
Two flapped chest pockets.

Pockets — position and depth

Pocket positions measured from the waistline, and pocket depths, in centimetres
Pocket	Centre below waistline	Depth
Flapped chest pocket, left and right	22 cm above	15 cm

Finished measurements

These are the measurements of the garment lying flat, not of a body. Every figure is in centimetres and is taken after washing.

Finished garment measurements in centimetres, by size
Size	Chest	Waist	Back length	Shoulder
34	96 cm	90 cm	66 cm	36.4 cm
36	100 cm	94 cm	67 cm	37.2 cm
38	104 cm	98 cm	68 cm	38 cm
40	108 cm	102 cm	69 cm	38.8 cm
42	112 cm	106 cm	70 cm	39.6 cm
44	116 cm	110 cm	71 cm	40.4 cm
46	120 cm	114 cm	72 cm	41.2 cm

Specification

Fabric weight: 210 g/m²
Fibre composition: 55 % cotton, 45 % polyester
Shrinkage: Up to 3 % in length and 2 % in width after the first 60 °C wash.
Origin: Designed in Mariefred. Country of making: [Pending — to be confirmed by the operator before launch].
Purchase type: Outright purchase. No subscription.
Classification: Workwear. Not personal protective equipment. Not certified to any protective standard.

Reinforced here

Armhole binding
Yoke seam
Pocket corners

What fails first

Workwear wears out, and it wears out in a predictable order. These are the places this garment gives up first, listed before you buy it rather than after.

1.Armhole binding edge
2.Side seam at the hip
3.Pocket corners

Wear at these points is wear, not a fault. A seam that opens in normal use, a failed zip, a reinforcement layer coming away, a garment that does not match the measurements above, or shrinkage beyond the stated range — those are faults. See Reklamation.

Care

Machine wash 60 °C, normal cycle.
Do not use fabric softener — it coats the twill and the fabric stops shedding dust.
Tumble dry low or line dry.
Iron medium. Do not iron over the hardware.
Wash before first wear so the shrinkage below has already happened when you check the fit.

Also cut for reach & climb

B-01

Work Shirt Basic

Plain long-sleeve work shirt. 150° overhead before the hem starts to lift.

Overhead reach: 150°
Back movement: 4 cm

$78USD

Figures

B-02

Work Shirt Action-Back

Two box pleats from the yoke. 170° overhead, and the hem stays at the hip.

Overhead reach: 170°
Back movement: 8 cm

$108USD

Figures

B-03

Work Shirt Gusset

Triangular gusset under the arm. Less bulk than a pleated back, 165° overhead.

Overhead reach: 165°
Back movement: 6 cm

$98USD

Figures